Valid 200-105 Exam Questions For Preparation

By | January 2, 2020

Make your 200-105 exam  easier and simpler. Our Cisco 200-105 exam practice test software which simulates the real exam testing environment.

Try it Latest DumpsSchool 200-105 Exam dumps. Buy Full File here: https://www.dumpsschool.com/200-105-exam-dumps.html (691 As Dumps)

Download the DumpsSchool 200-105 braindumps from Google Drive: https://drive.google.com/file/d/1TwCxP9R2WPXn5O77CUBND73niqczpZDp/view (FREE VERSION!!!)

Question No. 1

Which of these represents an IPv6 link-local address?

Answer: A

Understanding IPv6 Link Local Address

http://www.cisco.com/en/US/tech/tk872/technologies_configuration_example09186a0080ba1d07.shtml

The purpose of this document is to provide an understanding of IPv6 Link-local address in a network. A linklocal address is an IPv6 unicast address that can be automatically configured on any interface using the linklocal prefix FE80::/10 (1111 1110 10) and the interface identifier in the modified EUI-64 format. Link-local addresses are not necessarily bound to the MAC address (configured in a EUI-64 format). Link-local addresses can also be manually configured in the FE80::/10 format using the ipv6 address link-local command.

Question No. 2

The following configuration is applied to a Layer 2 Switch:

interface fastethernet 0/4

switchport mode access

switchport port-security

switchport port-security mac-address 0000.1111.1111

switchport port-security maximum 2

swithcport port-security

What is the result of the above configuration being applied to the switch?

Answer: B, D

Question No. 3

Which two statements about interior gateway routing protocols are true? (Choose two.)

Answer: A, C

Question No. 4

Which two data link layers are supported by Cisco IOS Software for IPv6? (Choose two.)

Answer: B, E

Question No. 5

What command visualizes the general NetFlow data on the command line?

Answer: C

The following is an example of how to visualize the NetFlow data using the CLI. There are three methods to visualize the data depending on the version of Cisco IOS Software. The traditional show command for NetFlow is “show ip cache flow” also available are two forms of top talker commands. One of the top talkers commands uses a static configuration to view top talkers in the network and another command called dynamic top talkers allows real-time sorting and aggregation of NetFlow data. Also shown is a show MLS command to view the hardware cache on the Cisco Catalyst 6500 Series Switch.

The following is the original NetFlow show command used for many years in Cisco IOS Software. Information provided includes packet size distribution; basic statistics about number of flows and export timer setting, a view of the protocol distribution statistics and the NetFlow cache.

R3#show ip cache flow

IP packet size distribution (469 total packets):

1-32 64 96 128 160 192 224 256 288 320 352 384 416 448 480

.000 .968 .000 .031 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000

512 544 576 1024 1536 2048 2560 3072 3584 4096 4608

.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000

IP Flow Switching Cache, 278544 bytes

7 active, 4089 inactive, 261 added

1278 ager polls, 0 flow alloc failures

Active flows timeout in 30 minutes

Inactive flows timeout in 15 seconds

IP Sub Flow Cache, 25736 bytes

1 active, 1023 inactive, 38 added, 38 added to flow

0 alloc failures, 0 force free

1 chunk, 1 chunk added

last clearing of statistics never

Protocol Total Flows Packets Bytes Packets Active(Sec) Idle(Sec)

——– Flows /Sec /Flow /Pkt /Sec /Flow /Flow

TCP-WWW 71 0.0 1 40 0.1 1.3 1.2

TCP-BGP 35 0.0 1 40 0.0 1.3 1.2

TCP-other 108 0.1 1 40 0.1 1.3 1.2

UDP-other 37 0.0 1 52 0.0 0.0 15.4

ICMP 3 0.0 5 100 0.0 0.0 15.3

Total: 254 0.2 1 42 0.4 1.1 3.5

(NetFlow cache below)

SrcIf SrcIPaddress DstIf DstIPaddress Pr SrcP DstP Pkts

Et1/0 172.16.7.2 Null 224.0.0.9 11 0208 0208 1

Et1/0 172.16.10.2 Et0/0 172.16.1.84 06 0087 0087 1

Et1/0 172.16.10.2 Et0/0 172.16.1.84 06 0050 0050 1

Et1/0 172.16.10.2 Et0/0 172.16.1.85 06 0089 0089 1

Et1/0 172.16.10.2 Et0/0 172.16.1.85 06 0050 0050 1

Et1/0 172.16.10.2 Et0/0 172.16.1.86 06 00B3 00B3 1

Et1/0 172.16.10.2 Et0/0 172.16.1.86 06 0185 0185 2

http://www.cisco.com/c/en/us/products/collateral/ios-nx-os-software/ios-netflow/prod_white_paper0900aecd80406232.html

Question No. 6

In an HSRP failover environment, which two tasks must you perform on the preferred active router so that it

always assumes the active role when it comes up? (Choose two.)

Answer: A, C

Question No. 7

Which command do you enter so that R1 advertises the loopback0 interface to the BGP

Peers?

Answer: A

Question No. 8

Which WAN technology is secure and encrypted by default?

Answer: A

Question No. 9

Assuming the default switch configuration, which VLAN range can be added, modified, and removed on a

Cisco switch?

Answer: B

Question No. 10

Which command do you enter to verify that a VLAN has been removed from a trunk?

Answer: A

Question No. 11

Refer to the exhibit.

Which problem is indicated by this error?

Answer: C

Question No. 12

What command sequence will configure a router to run OSPF and to add network 10.1.1.0/24 to area 0?

Answer: D

Question No. 13

Which configuration enables OSPF for network 192.168.1.0/24?

Answer: B

Question No. 14

Refer to the exhibit. The router has been configured with these commands:

What are the two results of this configuration? (Choose two.)

Answer: D, E

Question No. 15

Which feature can you implement to reserve bandwidth for voip calls across the call path?

Answer: D

200-105 Dumps Google Drive: (Limited Version!!!)
https://drive.google.com/file/d/1TwCxP9R2WPXn5O77CUBND73niqczpZDp/view

Related Certification: CCNA Routing & Switching dumps