Free Juniper JN0-661 Exam Dumps – [Feb-2018 Dumps]

By | February 27, 2018

Once you are up to appear in the Juniper Service Provider Routing and Switching JN0-661 exam. You may come across a variety of websites and platforms that will be facilitating you in achieving your goal. But afterwards you will find it that only a few of them provide you assistance to pass Juniper Service Provider Routing and Switching JN0-661 Exam. In order to pass Juniper JN0-661 Exam, the most important element is to check the quality of that particular Juniper Service Provider Routing and Switching exam dumps which you are selecting for dragging off your desired JN0-661 certification exam.

♥ VALID JN0-661 Exam Questions 2018 ♥

JN0-661 exam questions, JN0-661 PDF dumps; JN0-661 exam dumps:: https://www.dumpsschool.com/JN0-661-exam-dumps.html (133 Q&A) (New Questions Are 100% Available! Also Free Practice Test Software!)

Latest and Most Accurate Juniper JN0-661 Dumps Exam Questions and Answers:

Version: 8.0
Question: 21

You are asked to provide Layer 3 VPN services to a new customer site. The site will connect to the Layer 3 VPN using a Layer 2 switch. Which two configuration elements meet the requirement? (Choose two.)

A. vrf-table-label
B. vt interface
C. vrf-target
D. vrf-export

Answer: A B

Question: 22

Refer to the exhibit.

You are implementing a Layer 3 VPN between Site 1 and Site 2. You notice that you are not sharing routes between PE1 and PE2. You have verified that MPLS and RSVP are functioning correctly. Referring to the exhibit, what is causing the problem?

A. The multihop feature is not enabled.
B. The next hop for the VPN routes is unusable.
C. The Layer 3 VPN NLRI has not been enabled on PE1.
D. The PE2 BGP session is restarting.

Answer: C

Question: 23

Referring to the exhibit, you have configured an L3VPN that connects Site-1 and Site-2 together, but the BGP routes are being hidden on the PE routers. The topology in this scenario is shown below.
Site-1 > PE-1 > P-1 > P-2 > PE-2 > Site-2
Which two acttions would allow communication Site-1 and Site-2? (Choose two.)

A. Disable CSPF on under MPLS on P-1 and P-2.
B. Configure DGP on P-1 and P-2.
C. Enable RSVP for all interfaces on P-1 and P-2.
D. Enable LDP for all interfaces on all routers.

Answer: C, D

Question: 24

A layer 2 circuit (RFC 4447) is established between two PE routers to provide connectivity between two customer sites. Which two statements related to this deployment are true?

A. Kompella encapsulation is used in the data plane communications.
B. LDP must be used for the control plane communications
C. BGP must be used for the control plane communications.
D. Martini encapsulation is used in the data plane communications.

Answer: B, D

Question: 25

Referring to the exhibit, which router will be the RP?

A. R4 for all groups
B. R1 for group 224.1.1.11 and R4 for all other groups
C. R1 for all groups
D. R4 for group 224.1.1.12 and R1 for all other groups

Answer: A

Question: 26

You must ensure that r1’s IPv4 loopback address exists in r3’s inet 0 routing table
Referring to the exhibit, which statement is true?

A. An IPv4 unicast realm can be enabled on each router.
B. A policy can be configured on M to redistribute 172.16.100.1/32 into OSPFv2, which would cause r3 to eventually learn the route and place it into inet0.
C. A RIB group can be configured on r3 to copy that route into inet 0 because 172.16.100.1/32 exists in r3’s inet6.0 table
D. A policy can be configured on r1 to redistribute 172 16 100 1/32 into OSPFv3, which would cause r3 to eventually learn the route and place it into inet 0.

Answer: C

New Updated JN0-661 Exam Questions JN0-661 PDF dumps JN0-661 practice exam dumps: https://www.dumpsschool.com/JN0-661-exam-dumps.html