Free Cisco 300-080 Exam Dumps – [Jan_2018 Dumps]

By | January 23, 2018

Once you are up to appear in the Cisco Certified Network Professional Collaboration 300-080 exam. You may come across a variety of websites and platforms that will be facilitating you in achieving your goal. But afterwards you will find it that only a few of them provide you assistance to pass Cisco Troubleshooting Cisco IP Telephony and Video 300-080 Exam. In order to pass Cisco 300-080 Exam, the most important element is to check the quality of that particular Cisco Troubleshooting Cisco IP Telephony and Video exam dumps which you are selecting for dragging off your desired 300-080 certification exam.

♥♥ 2018 NEW RECOMMEND 300-080 Exam Questions ♥♥

300-080 exam questions, 300-080 PDF dumps; 300-080 exam dumps:: https://www.dumpsschool.com/300-080-exam-dumps.html (157 Q&A) (New Questions Are 100% Available! Also Free Practice Test Software!)

Latest and Most Accurate Cisco 300-080 Dumps Exam Questions and Answers:

Version: 10.0
Question: 21

A call from a SX20 in the BackBone (not shown) with a URI extension is dialing a HQ Ph 1 that is registered to the HQ CUCM. Determine if the call fails and if so, what are the two causes? (Choose two).

A. The call succeeds.
B. The call fails.
C. There are no issues, so the call succeeds.
D. The SIP port is incorrect on the Cisco Unified Communications Manager CUCM SIP trunk.
E. The Local Zone Match Rule state is disabled.
F. Rule name UCM2 is set to stop on Match

Answer: A, C

Question: 22

When the command utils dbreplication status is executed on the Cisco Unified Communications Manager CLI, which step should be taken next to check the database replication status?

A. View the activelog file.
B. Run the same command on all nodes of the cluster.
C. Restart the Cisco CallManager service.
D. The command utils dbreplication runtimestate must be run on the publisher.
E. The command utils dbreplication runtimestate must be run on the subscriber.

Answer: A

Question: 23

You configured a Cisco ISR G2 as a SIP gateway, but the gateway does not show that it is registered with Cisco Unified Communications Manager. What is causing this issue?

A. Cisco Unified Communications Manager does not support SIP gateways.
B. The gateway does not have the UC license installed.
C. The gateway does not have Cisco Unified Border Element session licensing.
D. Cisco Unified Communications Manager does not show a SIP gateway as registered if it is not properly configured.
E. Cisco Unified Communications Manager never shows a SIP gateway as registered even when it is properly configured.
F. The Cisco ISR G2 cannot be a SIP gateway.

Answer: E

Question: 24

Which issue would cause an MGCP gateway to fail to register with Cisco Unified Communications Manager?

A. missing the configuration command isdn bind-l3 ccm-manager under the ISDN interface
B. mismatched domain name on the MGCP gateway and Cisco Unified Communications Manager gateway configuration
C. misconfigured route group in Cisco Unified Communications Manager
D. incorrect MGCP IP address specified in the gateway configuration in Cisco Unified Communications Manager

Answer: B

Question: 25

Endpoints are configured for both H.323 and SIP using the same URI and Cisco VCS settings, but the endpoints register only as H.323 endpoints. What is causing this issue?

A. A firewall is blocking all traffic from the endpoints to the Cisco VCS.
B. The Cisco VCS has no SIP domains configured.
C. The Cisco VCS is blocking the endpoints because of duplicate ID entries.
D. The endpoints do not have the SIP option key installed.
E. SIP does not work, because SIP is used for Cisco Unified Communications Manager registration only.

Answer: B

Question: 26

You are trying to register an H.323-based Cisco TelePresence system to Cisco Unified Communications Manager and a Cisco DX70 system to the Cisco VCS Control. Why do neither of the units want to register?

A. The H.323-based system needs an E164 number to register to Cisco Unified Communications Manager, and the Cisco DX70 needs to have the MAC address configured first on the Cisco VCS Control.
B. The H.323-based system needs to register to the Cisco VCS Control with an E.164 number, and the Cisco DX70 needs the TFTP address to register on the Cisco Unified Communications Manager.
C. Both systems need to register to the Cisco VCS Control, but the H.323-based system needs to have the gatekeeper setting set to “Direct.”
D. Both systems need to register to the Cisco Unified Communications Manager, as the Cisco VCS Control is used only for firewall traversal.
E. You need Cisco TelePresence Management Suite to register Cisco TelePresence systems.
F. You need Cisco TelePresence Server to register Cisco TelePresence systems.

Answer: B

New Updated 300-080 Exam Questions 300-080 PDF dumps 300-080 practice exam dumps: https://www.dumpsschool.com/300-080-exam-dumps.html