Once you are up to appear in the Cisco Certified Design Associate 100-105 exam. You may come across a variety of websites and platforms that will be facilitating you in achieving your goal. But afterwards you will find it that only a few of them provide you assistance to pass Cisco Interconnecting Cisco Networking Devices Part 1 100-105 Exam. In order to pass Cisco 100-105 Exam, the most important element is to check the quality of that particular Cisco Interconnecting Cisco Networking Devices Part 1 exam dumps which you are selecting for dragging off your desired 100-105 certification exam.
100-105 exam questions, 100-105 PDF dumps; 100-105 exam dumps:: https://www.dumpsschool.com/100-105-exam-dumps.html (347 Q&A) (New Questions Are 100% Available! Also Free Practice Test Software!)
Latest and Most Accurate Cisco 100-105 Dumps Exam Questions and Answers:
Identify the four valid IPv6 addresses. (Choose four.)
Answer: A, B, E, F
Which two statements describe characteristics of IPv6 unicast addressing? (Choose two.)
A. Global addresses start with 2000::/3.
B. Link-local addresses start with FE00:/12.
C. Link-local addresses start with FF00::/10.
D. There is only one loopback address and it is ::1.
E. If a global address is assigned to an interface, then that is the only allowable address for the interface.
Answer: A, D
Which OSI layer header contains the address of a destination host that is on another network?
E. data link
Only network address contains this information. To transmit the packets the sender uses network address and datalink address. But the layer 2 address represents just the address of the next hop device on the way to the sender. It is changed on each hop. Network address remains the same.
Which layer of the TCP/IP stack combines the OSI model physical and data link layers?
A. Internet layer
B. transport layer
C. application layer
D. network access layer
The Internet Protocol Suite, TCP/IP, is a suite of protocols used for communication over the internet. The TCP/ IP model was created after the OSI 7 layer model for two major reasons. First, the foundation of the Internet was built using the TCP/IP suite and through the spread of the World Wide Web and Internet, TCP/IP has been preferred. Second, a project researched by the Department of Defense (DOD) consisted of creating the TCP/IP protocols. The DOD’s goal was to bring international standards which could not be met by the OSI model.
Since the DOD was the largest software consumer and they preferred the TCP/IP suite, most vendors used this model rather than the OSI. Below is a side by side comparison of the TCP/IP and OSI models.
Which protocol uses a connection-oriented service to deliver files between end systems?
TCP is an example of a connection-oriented protocol. It requires a logical connection to be established between the two processes before data is exchanged. The connection must be maintained during the entire time that communication is taking place, then released afterwards. The process is much like a telephone call, where a virtual circuit is established–the caller must know the person’s telephone number and the phone must be answered–before the message can be delivered.
TCP/IP is also a connection-oriented transport with orderly release. With orderly release, any data remaining in the buffer is sent before the connection is terminated. The release is accomplished in a three-way handshake between client and server processes. The connection-oriented protocols in the OSI protocol suite, on the other hand, do not support orderly release. Applications perform any handshake necessary for ensuring orderly release.
Examples of services that use connection-oriented transport services are telnet, rlogin, and ftp.
Refer to the exhibit.
If the hubs in the graphic were replaced by switches, what would be virtually eliminated?
A. broadcast domains
B. repeater domains
C. Ethernet collisions
D. signal amplification
E. Ethernet broadcasts
Modern wired networks use a network switch to eliminate collisions. By connecting each device directly to a port on the switch, either each port on a switch becomes its own collision domain (in the case of half duplex links) or the possibility of collisions is eliminated entirely in the case of full duplex links.
New Updated 100-105 Exam Questions 100-105 PDF dumps 100-105 practice exam dumps: https://www.dumpsschool.com/100-105-exam-dumps.html